Asko Appliance Specialists · Licensed & Insured · Serving 5 Major Metro Areas ☎ (844) 677-0530
Support and Repair
☎ (844) 677-0530 Schedule a Visit
Asko Tumble Dryer Repair

Tumble Dryer Repair, Done Right the First Time

Asko has sold vented, condensing and heat-pump tumble dryers in the United States, and they fail in different places, but the complaint that brings most of them to us is the same one: cycles that have quietly grown longer month by month until the machine no longer finishes a load.

Call (844) 677-0530 Schedule a Visit

Book Tumble Dryer Repair

Same-day & next-day appointments · No hidden fees · Technicians trained on these appliances

or call (844) 677-0530 now

A dryer heats air, moves it through a tumbling load and then gets rid of the moisture, and the third of those is where the machines differ. A vented model pushes it outside through a duct. A condensing model cools it back to water and pumps it into a tank. A heat-pump model does the same but recovers the heat instead of discarding it, which is why its cycles run cooler and longer and why its condenser is more sensitive to a coating of lint.

That is the reason the diagnosis starts at the airflow on every call. A door filter that is cleaned but not rinsed, a condenser unit that has never been taken out, a duct crushed behind the appliance, or a small closed laundry room with no cool air reaching the machine will all produce the same complaint – long cycles and damp laundry – and none of them is a failed part.

Once the air path is proven clear, the electrical side is short and testable: heating components and their thermal protection, the thermistor, the humidity sensing, the condensate pump, the drive motor and belt, the door switch and the control boards. We isolate the circuit and let the machine cool before a panel comes off, and where a repeated fault has an underlying cause – a blocked condenser behind an overheat cut-out, for instance – we deal with the cause as well as the part, because otherwise the same visit is booked again in a month.

Common Tumble Dryer Problems

01

Cycles taking noticeably longer than they did a year ago

02

Clean door filter or Clean the condenser unit appearing at the end of a program

03

The water tank reported full shortly after it was emptied

04

E4 on the display asking for the filters to be cleaned

05

Drum turning with no heat reaching the load

06

Program stopping early and leaving the load damp

Tumble Dryer Error Codes

Recognize a code on your display? Look it up before you unplug anything or attempt a repair.

E0

Asko Dryer Error 0 Code (Control Unit Failure)

E1

Asko Dryer Error 1 Code (Thermistor Fault, Temperature Sensor Failure)

E2

Asko Dryer Error 2 Code (Communication Error)

E3

Asko Dryer Error 3 Code (Condensate Pump Failure)

E4

Asko Dryer Error 4 Code (Clean the Filters)

E6

Asko Dryer Error 6 Code (Relay Failure, Control Unit)

E7

Asko Dryer Error 7 Code (Door Failure, Control Unit)

E8

Asko Dryer Error 8 Code (Button Failure, Control Unit)

E9

Asko Dryer Error 9 Code (Board and Interface Software Versions Not Compatible)

F1

Asko Dryer F1 Code (Condensation Water Tank Full on TD60.1 Machines)

F2

Asko Dryer F2 Code (Maximum Programme Time Reached on TD60.1 Machines)

See all Error Codes →

Popular Asko Tumble Dryer Models

Asko 7703 Tumble Dryer

Model # 7703

Asko 7704 Tumble Dryer

Model # 7704

Asko 7705 Tumble Dryer

Model # 7705

Asko T731 Tumble Dryer

Model # T731

Asko T780B Tumble Dryer

Model # T780B

Asko TL751GXXLRR Tumble Dryer

Model # TL751GXXLRR

Why Trust Us With Your Asko Tumble Dryer

  • Measured, Not Guessed | The suspect tumble dryer component goes on a meter and is shown to have failed before we recommend replacing it.
  • Common tumble dryer Parts Aboard | The parts that fail most often travel with the technician; anything rarer is ordered on the spot and the return visit booked before we leave.
  • Isolated Before Anything Opens | The supply to your tumble dryer - power and water - is shut off and proven dead before a panel moves, and high-voltage circuits stay with the technician.
  • Coverage Checked First | Where your tumble dryer looks like it may still sit inside manufacturer coverage we flag it before quoting, so you can decide which route costs you less.
FAQ

Tumble Dryer Repair FAQ

Most of them point inside the appliance. Asko gives E0 as a control unit failure, E1 a temperature sensor failure, E2 a communication error, E3 a failure of the pump that moves condensate into the tank, E6 a relay failure, E7 a door failure, E8 a button failure and E9 a software version mismatch between the boards. The one written for the owner is E4, which asks for the filters to be cleaned. There is no E5 in Asko's table, so any list that gives one a meaning is not describing this appliance.

Several of them. Clean door filter, Clean the condenser unit and Please empty the water tank and clean door filter are maintenance prompts rather than failures. Steam tank is empty. Please fill water and Steam tank full belong to the steam function. Cycle was interrupted by power failure. Please resume means exactly what it says. Child lock is on. Press buttons for 3 sec to unlock explains a panel that appears to be dead. None of those needs a technician.

Let the machine finish and cool before you open anything, then work outward along the lint path with the appliance switched off at the breaker. The door filter loads on every cycle; the condenser unit behind the lower panel loads slowly across months, and that is what turns a gradual slowdown into a machine that never finishes. Asko puts the same reasoning in its own older manual under F2: empty the condensate container, check that neither the fluff filter nor the condenser is clogged, and give the appliance access to cooler air if it stands in a small, closed room where the air it is using has already been heated.

They belong to the TD60.1 panel and neither is a component failure. F1 means the condensation water container is full, and the instruction is to empty it and restart. F2 means the maximum permitted program time was reached, which Asko treats as a filter, condenser and ventilation question rather than as a repair. The later TD60.2, TD60.3, TD70 and TDC44 machines dropped numbers and print messages instead - Over flow, Max Program Time, Clean condenser, Clean Lint Filter, Thermistor fault - and those are reset by switching the machine off at the main power switch once the cause has been dealt with.

Up to a point. The lint path, the drum, the belt, the door and the control are common ground. What is particular to the heat-pump and condensing machines is the condenser unit, the condensate pump and the tank circuit - the parts behind E3 and behind the repeated tank-full messages - and none of those exists on a vented model, where the moisture leaves through the duct instead. Telling us which type you have when you book decides what the technician brings.

Need a repair? We're ready to help. Call Now